8524 Precision tension and compression load cell

compact, uncomplicated, universally applicable, easy integration into existing structures, for static, quasi-static and dynamic tensile and compressive forces, stainless steel, overload stop (option)

New order codes!

Product Inquiry

    Product comparison

      • Features

        • Measuring ranges from 0 ... 500 N to 0 ... 200 kN
        • Relative non-linearity: ≤ ±0.1 % F.S.
        • Output signal 1.5 mV/V, standardized
        • Highly versatile and for universal use
        • Type of protection acc. EN 60529 IP67 for measuring ranges ≥ 0 ... 20 kN
        • Cable suitable for drag chains and highly flexible
        • burster TEDS optionally available
      • Product data

        Model 8524
        Measuring range

        0 … 500 N
        0 … 1 kN
        0 … 2 kN
        0 … 5 kN
        0 … 10 kN
        0 … 20 kN
        0 … 50 kN
        0 … 100 kN
        0 … 200 kN

        Direction of force Tension and compression
        Standardization Yes
        Signal output 1.5 mV/V
        Protection class

        IP65 for measuring ranges ≤  0 ... 10 kN
        IP67 for measuring ranges ≥ 0 ... 20 kN

        Overload protection Option
        Pull-plate Option
        Load introduction button Option
        Range of operating temperature -30 ... +80 °C
        Specific characteristics

        • Output signal 1.5 mV/V, standardized
        • Highly versatile and for universal use
        • Type of protection acc. EN 60529 IP67 for measuring ranges ≥ 0 ... 20 kN
        • Relative non-linearity: 0.1 % F.S.
        • Cable suitable for drag chains and highly flexible
        • burster TEDS optionally available
      • Description

        The 8524 precision tension & compression load cell is a versatile sensor for highly accurate load measurements in diverse applications. Optimum measurement quality is achieved with the load cell mounted on a flat, hard and polished contact surface. This requirement does not apply to small measurement ranges of up to 0 ... 2 kN because three knife-edge bearings ensure that the sensor is seated securely. Off-center forces, bending moments and torques of less than 5% of the rated load will not impair the sensor‘s measurement quality. Our brochure „Load Cells“ explains how you can design parasitic loads out of your mechanical system.

        Through-holes in the outer flange are used for fastening the 8524 sensor to the system structure. The load is applied via the central blind threaded hole or optionally via a load button. Alternatively, a pull plate and even rod end bearings, if desired, can be attached to the sensor for equally easy measurement of purely tensile loads, for instance in Bowden cables or chains. The 8524 sensor is designed to measure static, quasi-static and dynamic compressive and/or tensile loads.

        Inside the sensor is an elastic membrane, on which are applied strain gages connected in a full Wheatstone bridge. If a tensile or compressive load is applied to the sensor, the ohmic resistance of the measuring bridge changes and detunes the output signal in proportion to the measured load in mV/V.

      • Data Sheet & Downloads

        Data sheet
        Brochure
        Operation manual
        Further info
      • Accessories

        pdf Rod ends with internal/external thread for force introduction
      • Videos

        Example showing load cell fitted under pre-load with extreme overload protection


        Youtube channel Burster Youtube Channel




      burster in Germany

      burster praezisionsmesstechnik gmbh & co kg
      +49 7224645-0
      infoburster.com
      www.burster.com

      Company-Information Company-Information

      Germany

      burster praezisionsmesstechnik gmbh & co kg

      Talstr. 1-5
      76593 Gernsbach
      Germany

      Fon: +49 7224645-0
      Fax: +49 7224645-88
      infoburster.com
      www.burster.com

      Trade fairs

      The Battery Show
      30.11. - 02.12.21 - Stuttgart, 70269, Germany  

      ×
      © 2021 // burster präzisionsmesstechnik gmbh & co kg
      nach oben